C.Y. Khor

About

C.Y. Khor (Chu Yee Khor) received the bachelor degree in mechanical engineering, and the M.Sc and Ph.D. degrees in Mechanical Engineering, specializing in electronic packaging from Universiti Sains Malaysia, Minden, Malaysia, in 2008, 2010 and 2013, respectively. He was a Post-Doctoral Fellow at School of Mechanical Engineering, Universiti Sains Malaysia, 2014. Currently, he is a senior lecturer at the Faculty of Engineering Technology, Universiti Malaysia Perlis (UniMAP), Perlis, Malaysia. Dr Khor is a journal reviewer of Microelectronics Reliability, Heat and Mass Transfer, International Journal of Heat and Mass Transfer, Arabian Journal for Science and Engineering, Soldering & Surface Mount Technology, Journal of Electronic Packaging, Microelectronics International, etc.

Employment

• Universiti Malaysia Perlis Senior Lecturer
  2020 - Present
• Universiti Malaysia Perlis Senior Lecturer
  2015 - 2020
• Universiti Sains Malaysia Kampus Kejuruteraan Post-Doctoral Researcher
  2014 - 2015
• Universiti Sains Malaysia - Kampus Kejuruteraan Seri Ampangan PhD Researcher
  2010 - 2013
• Universiti Sains Malaysia - Kampus Kejuruteraan Seri Ampangan Research Officer
  2010 - 2011
• Universiti Sains Malaysia - Kampus Kejuruteraan Seri Ampangan Research Assistant
  2008 - 2009

Education

• Universiti Sains Malaysia Kampus Kejuruteraan B.Eng (Hons); M.Sc.; Ph.D
  2010 - 2013

Projects & Funding

Projects & funding information is unavailable.

Publications (138)

• Crashworthiness performance of thin-walled structures towards design configuration in vehicle crash boxes application: a review
  International Journal of Crashworthiness 2025 DOI: 10.1080/13588265.2025.2492975
  +Save
• Thermal performance optimization for a tapered heat sink of bus bar conductor using definitive screening design
  Mark Selvan, Mohd Sharizal Abdul Aziz, Nurulakmal Mohd Sharif +4 more
  International Journal of Thermal Sciences 2025 DOI: 10.1016/J.IJTHERMALSCI.2024.109414
  +Save
• A Short Review on Multi-stage Application in Fluidization Systems
  Lecture Notes in Mechanical Engineering 2021 DOI: 10.1007/978-981-16-0866-7_60
  +Save
• A simulation on influence of cooling at rake face to tool temperature
  Journal of Physics: Conference Series 2021 DOI: 10.1088/1742-6596/2051/1/012052
  +Save
• Computation Fluid Dynamics Simulation of Airflow Ventilation System in 3D Indoor Mushroom Cultivation House Model
  Lecture Notes in Mechanical Engineering 2021 DOI: 10.1007/978-981-16-0866-7_61
  +Save
• Computational analysis of airflow in upper airway under light and heavy breathing conditions for a realistic patient having obstructive sleep apnea
  CMES - Computer Modeling in Engineering and Sciences 2021 DOI: 10.32604/CMES.2021.015549
  +Save
• Conceptual Design Selection of Motorcycle Handle Brake Lever Component by TRIZ and Simulation
  Lecture Notes in Mechanical Engineering 2021 DOI: 10.1007/978-981-16-0866-7_110
  +Save
• Influence of Twisted Blades Distributor Towards Low Pressure Drop in Fluidization Systems
  Lecture Notes in Mechanical Engineering 2021 DOI: 10.1007/978-981-16-0866-7_59
  +Save
• Influence of inlet velocity and heat flux on the thermal characteristic of various heat sink designs using CFD analysis
  Journal of Physics: Conference Series 2021 DOI: 10.1088/1742-6596/2051/1/012013
  +Save
• Mechanical Design and Analysis of Safety Medical Syringe for Needlestick Injury Prevention
  Lecture Notes in Mechanical Engineering 2021 DOI: 10.1007/978-981-16-0866-7_58
  +Save
• Minimizing warpage and shrinkage of plastic car rear bumper fabrication via simulation based optimisation
  Journal of Physics: Conference Series 2021 DOI: 10.1088/1742-6596/2051/1/012012
  +Save
• Multi Response Optimization of Injection Molding Parameters for Artificial Phalanx Bone Using Response Surface Methodology
  Lecture Notes in Mechanical Engineering 2021 DOI: 10.1007/978-981-16-0866-7_75
  +Save
• Numerical Simulation of Transesterification Reaction in Y-Shaped Microreactor
  Lecture Notes in Mechanical Engineering 2021 DOI: 10.1007/978-981-16-0866-7_113
  +Save
• Optimisation of Process Parameters in Plastic Injection Moulding Simulation for Blower Impeller’s Fan Using Response Surface Methodology
  Lecture Notes in Mechanical Engineering 2021 DOI: 10.1007/978-981-16-0866-7_26
  +Save
• Optimization of flexible printed circuit board’s cooling with air flow and thermal effects using response surface methodology
  Microelectronics International 2021 DOI: 10.1108/MI-06-2021-0049
  +Save
• Simulation Based Optimization of Shrinkage in Injection Molding Process for Lamp Holder via Taguchi Method
  Lecture Notes in Mechanical Engineering 2021 DOI: 10.1007/978-981-16-0866-7_27
  +Save
• The modified phase inversion and sintering technique for fabrication of ceramic membrane: Influence of kaolin composition and drying temperature
  AIP Conference Proceedings 2021 DOI: 10.1063/5.0044560
  +Save
• Biomechanical assessment of different surgical approaches of zygomatic implant placement on prosthesis stress
  IOP Conference Series: Materials Science and Engineering 2020 DOI: 10.1088/1757-899x/932/1/012108
  +Save
• Computational Fluid Dynamics (CFD) Simulation on Mixing in T-Shaped Micromixer
  IOP Conference Series: Materials Science and Engineering 2020 DOI: 10.1088/1757-899x/932/1/012006
  +Save
• Effect of heat sink design on the thermal characteristic in computational fluid dynamics analysis
  IOP Conference Series: Materials Science and Engineering 2020 DOI: 10.1088/1757-899x/932/1/012106
  +Save